Choose your vehicle to get started

chooser arrow chooser arrow

Will the Unichip increase my low end torque and my high end horsepower?

Short answer - Yes

Long answer - Although they're commonly synonymous with high and low rpm performance, horsepower and torque do not represent the same thing and they are not produced at different parts of the engine power curve.  Unlike bolt-on modifications, with the Unichip your engine can create more torque at all rpm's which, in turn, means your engine makes more horsepower at all rpm's. 

 

Technical answer - Although the terms horsepower and torque are often incorrectly used interchangeably, they actually describe different phenomena.  Torque is power.  Horsepower is work.

 

     o  Power is the rotational twist about an axis caused by a force acting at a distance (called a moment arm) from that axis...

 

T = r x F

 

Where r equals the length of the distance between the where the force is applied and the center of rotation and F is the amount of force.  

 

     If you place a wrench on a bolt, the amount of force you apply to the wrench and the length of the wrench determine the amount of torque - or twist - applied to the bolt.  If the wrench is two feet long, and you pull with 100 pounds of force, you're twisting the bolt with 200 lb-ft of power... or torque.  

 

     o Work is the amount of power made at a given rate... a far more nebulous but very important concept.  There are many types of horsepower, but for an internal combustion engine discussion, the one you're interested in is mechanical or brake horsepower, abbreviated bhp.  Bhp isn't directly measured but is calculated from Torque using the equation...

 

bhp = T x rpm/5252

 

Where T is torque, rpm is engine speed, and 5252 is a constant.

 

What this equation tells us is...

- Engines create bhp at all rpm's and for any value of T there is a corresponding bhp value

- Engines create T at all rpm's and for any value of bhp there is a corresponding T value

- Anytime rpm is less than 5252, bhp < T

- Anytime rpm is greater than 5252, bhp > T

- Anytime rpm equals 5252, bhp = T

 

     So why to diesel truck guys rarely mutter the letters bhp?  Most TDi engines redline well below 4000 rpm which - putting the numbers into the equation above, means bhp is at least 25% less than T and since bigger is always better... 

     A 6.0 turbo diesel truck engine making 600 lb-ft is certainly something to brag about... but the 285 bhp its making isn't much more than a typical family sedan.  How can something making only 286 bhp pull a 6000 lb trailer at 70 mph down the highway?  It's not because it "uses torque."

     For exactly the opposite reason, while the F1 crowd justifiably brags about 2.4L normally aspirated engines making 800 bhp, you won't hear them mentioning that while the engine is cranking out that bhp at 18,000 rpm, it's only making 232 lb-ft.  How can an engine only making 232 lb-ft torque accelerate a car from 0-60 in less than 3 seconds and push a car in excess of 200 mph?  It's not because it "uses horsepower."

     In reality, both the diesel truck and F1 engines perform well when put into vehicles designed to take advantage of their strengths... diesel trucks need to pull strongly at low rpm so they last for years while F1 cars must be very light and produce very high power for short race periods.

     Engineers design drive trains to allow those engines to work efficiently while the vehicle does what it's designed to do.  To understand that efficiency, you have to look at the transmission/final drive gear ratios and where the engine is at its peak torque. 

 

     As you look at the following examples, consider two pretty common experiences...

 

     o   First, I talked about using a 2 foot long wrench to torque a bolt to 200 lb-ft which is a good pull but still something most guys could easily do.  That's no more Torque than most small car engines produce so why don't we have human powered cars?  It's not the power, it's the work.  While the car engine makes the same 200 lb-ft of power, it can do it while spinning the bolt at 5000 rpm.  You can make the power, but at about 2 rpm... for about 2 minutes, while the car's engine can do it until it runs out of fuel.

 

     o   Next, think about riding a multi-speed bicycle and what happens to speed and your legs as you work your way up through the gears.  If you put out a constant amount of power, in lower gears you accelerate quickly but don't go very fast while in higher gears you accelerate slower but go faster.  Just like your legs, the engines in the truck and the car always do the same amount of work at a given rpm... what changes is what gear the transmission is in.  Even though power doesn't change, work does...

 

     With that in mind, consider a "typical" diesel truck and a "typical" F1 car in three different situations... first at 30 mph, then at 60 mph, and finally at 120 mph... and let's see what they're doing.

 

Engine rpm
Drive wheel rpm
Flywheel T
Drive wheel T
Flywheel bhp
Drive Wheel bhp

1568

294

600 lb-ft

3120 lb-ft

179 bhp

955 bhp

8000

727

200 lb-ft

2200 lb-ft

304 bhp

3351 bhp

 

     At 30 mph, the truck engine is spinning at just 1568 rpm, is in the heart of it's power band, and with the drive train's 5.33-1 total mechanical advantage the truck is putting some impressive numbers to the drive wheels and it's ready to uproot some trees.  This is what the truck is built to do and this is the spot it's built to do it in.

     The F1 engine is also at a moderate 8000 rpm (for an F1 engine that is, they idle at ~ 6000 rpm) and is still well below it's power band but because the engine is spinning so much faster than the drive wheels, the engine enjoys an 11-1 total mechanical advantage through the drive train allowing it to also put some impressive numbers to the drive wheels.  You can see why these cars that weigh under 1400 lbs including the drivers accelerate like they do.

 

Engine rpm
Drive wheel rpm
Flywheel T
Drive wheel T
Flywheel bhp
Drive Wheel bhp

1951

786

500 lb-ft

1241 lb-ft

186 bhp

461 bhp

14000

1454

225 lb-ft

2166 lb-ft

600 bhp

5777 bhp

 

     At 60 mph, things are changing.  The truck has shifted into fifth gear because of the engine's low redline and the engine is already moving out the top of it's peak power band as the engine's volumetric efficiency begins to exceed the turbo's capability.  The engine is still making 83% of the power it made above, but the work being done through the gears at the tire contact patches have decreased by almost 70% because the mechanical advantage is down to 2.48 as the transmission is running out of gears. 

     The F1 car is still in first gear and approaching it's power band and - because of the engine's very high redline - still enjoys the 11-1 mechanical advantage... while the truck's road wheel power is way down, the F1 car's power at the contact patch has almost doubled.

 

Engine rpm
Drive wheel rpm
Flywheel T
Drive wheel T
Flywheel bhp
Drive Wheel bhp

2925

1179

400 lb-ft

992 lb-ft

223 bhp

552 bhp

18000

2903

233 lb-ft

1445 lb-ft

798 bhp

4951 bhp

 

     At 120, the story is complete.  The truck is still in fifth gear, the engine is running out of available rpm, and power is starting to noticeably fall off... flywheel power is down by 50% compared to 30 mph and second gear while drive wheel power is down by 75%.   As power is falling off, aerodynamic drag is increasing exponentially and the truck has literally hit a wall.  This isn't what a full size truck is meant to do and it shows.

     The F1 car, on the other hand, is like a dog that just got off it's leash and doing exactly what it was designed for.  The engine is screaming at redline making its peak power and the car is in third gear pulling hard against the increasing resistance of the air.  Although drive wheel power is down because of the decreased mechanical advantage as the driver up shift, it's still 45% higher than the truck and the car still has four more gears to go.  It can't uproot a tree, but with 1445 lb-ft and 4951 bhp at the drive wheels and several gears to go, it's going to pull hard well past 200 mph.

 

     o   Unichip tuning.  So with the understanding that an engine has "torque" at every rpm and "horsepower" at every rpm, what do you get when you install a Unichip?

     When we build calibrations, we optimize the Air-Fuel Ratio and ignition timing (or injection timing for TDi applications) so that all engine rpm at high load the combustion chamber produces maximum power... maximum Torque. 

      With the Unichip, at 1000 rpm, the engine makes maximum torque and it does so at every rpm value all the way to redline.   That means - by definition - maximum bhp at every rpm as well.  So, whether you want to talk about power or work, Torque or bhp, the Unichip produces the most your engine will make.

 

No Footprint

With The Unichip there is no footprint. If you take your vehicle to the dealer for service work you can easily remove the Unichip which leaves no footprint that the Unichip was ever installed on your vehicle

THE POWER IS IN THE DISPLAY

Unlock the Unichip's full potential with Flux2 . Featuring Unichip Map-Command

Become A Unichip Certified Tuner

Get free support and increase sales with unlimited capabilities

Get more from the Unichip

Learn about the many options we offer

Tune Into Our

Jobbers Wanted, exciting new opportunities